Description :

The SF100 is a high speed “In System Programming” programmer to update the SPI Flash soldered on board or Freescale MCU using Ezport. The programmer is easily controlled by the computer DediProg Software through the USB bus offering friendly interface and powerful features to users.

Features :

Update Serial Flash soldered on board with application powered or not

Update the internal Flash of Freescale MCU using the Ezport (MCF5223, MCF5221, MCF5213) or the external SPI Flash of Freescale MCU using the SBF interface (MCF5445, MCF5227)

Control Application, controller reset and MOSFET isolation status

Capable of handling two serial flash memories;(new feature; provided in SF100 with serial number DP001325, firmware 2.0.4, software 2.0.37 and after)

USB Interface

Start button feature

Signal conflict protections

Multi-Programmers Capability

Support Windows 2003 and above

Support both 32 bit or 64 bit OS

 

 The SF100 USB software tool chain offers high flexibility and fit the different and highest requirements:

- Engineering Graphic User Interface: 

for engineers and expert to access advanced features for development, repairing etc.

 

 

 

 

 

- Production Graphic User Interface: 

for operators in production to control multiple programmers and improve the throughput.

 

 

- Command line interface: 

Customer software can control the multi SF100 programmers (SF100 integration, Control SF100 with Production In Circuit Tester..)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

High performance(tested and measured with software version 2.0.37.2 and from a single source of serial flash memory supplier): 

USB Mode

 

 

 

 

 

Density

8Mb

16Mb

32Mb

64Mb

128Mb

Program

7.28s

13.09s

28.01s

52.4s

74.01s

Verify

2.57s

4.64s

8.08s

17.09s

33.78s

Auto(Program+Verify)

8s

14s

37s

70s

108s

 
Hardware :

SF100 is designed with ISP header, through an appropriate connector; users can connect the programmer and drive the SPI signals, supply the memory and control the controller or application status. Please refer to Table 1 for the SF100 2x7 header pin out.

DediProg also provides the SF100 ISP Cable which is used to connect the SF100 programmer to the 2X4 2.54mm ISP Pin Header on board, please refer to Table 2 for the SF100 ISP Cable 2x4 pin out.

Table 1: SF100 ISP Header Pin Out (2x7) 

1

I/O1

I/O4

2

3

I/O2 or CS2

NC

4

5

Vcc

GND

6

7

CS

CLK

8

9

MISO

MOSI

10

11

Vpp/Acc

I/O3

12

13

SCL

SDA

14

Table 2: ISP Cable Connector Pin Out (2x4) 

1

Vcc

GND

2

3

CS

CLK

4

5

MISO

MOSI

6

7

Vpp/Acc

I/O3

8

 

 

 

 

 

 

 Contents :

1x USB cable

1x SF100 Programmer

1x ISP cable

 

1x SF100 Universal Adaptor

CDROM with Software, specifications and user manual

Hardware Requirement for ISP :

To have a clear understanding on the different ISP or backup boot methods and different reference schematics, please download our dedicated application notes: AN0103 and AN0106 in the documentation section

Option Purchase :

Backup Boot Flash-SO8N

Backup Boot Flash-Dual SO8N

Backup Boot Flash-SO8W

Backup Boot Flash-Dual SO8W

 

Backup Boot Flash-SO16W

Backup Boot Flash-Dual SO16W

BBF SO8 Testclip

BBF SO8 Testclip-Dual

 

BBF SO16W Testclip

ISP SO8 Testclip

ISP SO16W Testclip

SF100 Universal Adaptor