Description :

EM100Pro is DediProg Serial Flash Emulator based on RAM memory in order to offer the best update performances. This advanced tool has been designed in close cooperation with the Serial Flash suppliers to emulate the behaviors of all the market Serial Flash and also the next generation Serial Flash.

EM100pro emulator provide engineers with a flexible development and testing tool for any embedded project that uses an external SPI Flash. It provides quick, in-circuit firmware test cycles during development.

EM100pro increases productivity by downloading firmware code or data into the emulator in a few seconds for density as large as 512Mb. It further provides “SPI BUS Analyzer” feature by collecting all the SPI commands on the SPI bus in order to help for the debugging process.

EM100pro will speed up your firmware development and testing by eliminating the need to remove-erase-program and re-install SPI flash each time you test a code change.

If you want to stop the "program/insert/boot/remove/erase" cycle, then this is the tool for you

Features :

  • Emulate all the market Serial Flash in one click
  • Support up to two 256Mb or one 512Mb SPI flash emulation
  • Support Dual IO & Quad IO
  • Support Dual flashes emulation
  • Update code in less than 3 seconds
  • USB powered & palm size
  • Support Windows 2003 and above & Support both 32 bit or 64 bit OS

Benefits :

  • Minutes becomes seconds for SPI Flash code update (3 seconds to update 512Mb SPI Flash)
  • Save up to 1 hours every days for your development and reduce your time to market
  • Debug efficiently your application through the available SPI bus with our SPI Trace, SPI Trigger, SPI Hyper Terminal for debug messages
  • Develop your own application debugger via our bidirectional SPI Hyper terminal and control application from your host PC
  • EM100Pro can connect with Intel motherboard by specific adaptor ISP-ADP-Intel-B (Option). Click HERE for further information.
SPI Flash Emulation Interface SPI Bus Trace Interface
SPI Hyper Terminal Interface 　
　
Performance (Erase+Program+Verify)
Density     8Mb     16Mb     32Mb     64Mb     128Mb     256Mb     512Mb
Programmer 9s 13s 16s 38s 75s 115s 200s
EM100Pro 3s 3s 3s 3s 3s 3s 3s

*The compare data of programming speed is according to DediProg SF600 SPI Flash programmer.

Hardware :

The EM100Pro has two 2.54mm pitch males connectors of:

  • 2x2 for the Reset and Trig signals
  • 2x10 for the Emulation signals
EM100Pro is designed with ISP header, through an appropriate connector, users can connect the programmer and drive the SPI signals, supply the memory and control the controller or application status. Please refer to Table 1 for the EM100Pro 2x10 header pin out.
DediProg also provides the EM100Pro ISP Cable which is used to connect the EM100Pro programmer to the 2X5 2.54mm ISP Pin Header on board, please refer to Table 2 for the EM100Pro ISP Cable 2x5 pin out.
Table 1: EM100Pro ISP Header Pin Out (2x10),(2x2) 　 Table 2: ISP Cable Connector Pin Out (2x5)
1 Hold2 CS2 2
3 CS1 Vcc 4
5 MISO/DQ1 Hold1/DQ3 6
7 Wp1/DQ2 CLK 8
9 GND MOSI/DQ0 10
11 3.3V Wp2 12
13 CTRL NC 14
15 CTRL 3.3V 16
17 CTRL CTRL 18
19 GND CTRL 20

1 GND Reset 2
3 GND Trig 4
　

　
1 Hold2 CS2 2
3 CS1 Vcc 4
5 MISO Hold1 6
7 Wp1 CLK 8
9 GND MOSI 10
Contents :
  • 1 x EM100Pro
  • 1 x USB 2.0 cable
  • 1 x AC switching power adaptor
  • 1 x 2.54mm 2x10 to 2.54mm 2x5 cable
  • 1 x 1.27mm 2x4 to 1.27mm 2x4 cable
  • 1 x 1.27mm 2x8 to 1.27mm 2x8 cable
  • 1 x 2.54mm 2x10 to 1.27mm 2x4/2x8 SO connection adaptor
  • 1 x 12cm EM100Pro split cable
  • 1 x EM100Pro DIP cable 
 　
  • 4 x 1.27mm 2x8 SMT male header  (10.3mm)
  • 4 x 1.27mm 2x4 SMT male header (6.0mm)
  • 4 x 1.27mm 2x4 SMT male header (10.3mm)
  • 3 x 15cm single wire with 2.54mm Dupont head
  • 1 x EM100Pro Reference Flash Adaptor (SO8W)
  • 1 x EM100Pro Reference Flash Adaptor (SO16W)
  • 1 x Grabber Clip
  • 1 x CD-ROM (Included Software and user manual)