Description :

SF600Plus is high speed "in System Programming" programmer to update the SPI Flash soldered on board (In Circuit Programming) or in the socket adaptor (Off line programming). The programmer is easily controlled by the computer DediProg Software through the USB bus offering friendly interface and powerful features to users.

SF600Plus combines the advantages of SF100 with additional improvements:- High speed USB - Higher SPI performances - Support Single, Dual and Quad IO (ISP mode only).

SF600Plus is an upgrade version of SF600. The main difference is that SF600Plus embeds a 4Gb memory which allows standalone programming.

Features :

  • USB High speed and high SPI performance, support up to 1Gb SPI Flash
  • In circuit Programming: Program on board SPI Flash
  • Off line Programming: Program SPI Flash in the socket
  • Start button feature: Can do Batch function in USB mode
  • Standalone mode :Embedded 4Gb memory can update the Serial Flash without computer
  • Support Single, Dual and Quad IO serial communication (new serial Flash protocol)
    •
  • Program two Serial Flash memories
    •
  • Signal conflict protections
  • Multi-Programmers Capability through USB
  • Support 1.8V low voltage IC
  • Support Windows 2003 and above
  • Support both 32 and 64 bit OS
    •

The SF600Plus USB software tool chain offers high flexibility and fit the different and highest requirements:
Engineering Graphic User Interface:
For engineers and expert to access advanced features for development, repairing etc.		 Production Graphic User Interface:
For operators in production to control multiple programmers and improve the throughput.		 Command line interface:
Customer software can control the multi SF600Plus programmers.

High performance(12MHz, Quad IO):

USB Mode

Memory size
Reference IC W25X80VSIG W25Q16VSIG W25Q32FVSIG W25X64BVFIG W25Q128BFIG W25Q256FVFIG S25FL512SDF01
Density 8Mb 16Mb 32Mb 64Mb 128Mb 256Mb 512Mb
 (Program + Verify) 9s 13s 16s 38s 75s 115s 199.5s

*Please note the programming and verify time will depends on different IC type; please refer to the IC specification before programming.

Hardware :

SF600Plus is designed with ISP header, through an appropriate connector, users can connect the programmer and drive the SPI signals, supply the memory and control the controller or application status. Please refer to Table 1 for the SF600Plus 2x10 header pin out. DediProg also provides the SF600Plus ISP Cable which is used to connect the programmer to the 2X6 2.54mm ISP Pin Header on board, please refer to Table 2 for the SF600Plus ISP Cable 2x6 pin out.

Table 1: SF600Plus ISP Header Pin Out (2x10)
1 Vpp CS2 2
3 CS1 Vcc 4
5 MISO/DQ1 Hold/DQ3 6
7 Wp/DQ2 CLK 8
9 GND MOSI/DQ0 10
11 NC Reset/IO3 12
13 NC NC 14
15 NC NC 16
17 NC NC 18
19 GPIO1 GPIO2 20
Table 2: ISP Cable Connector Pin Out (2x6)
1 Vpp CS2 2
3 CS1 Vcc 4
5 MISO/DQ1 Hold/DQ3 6
7 Wp/DQ2 CLK 8
9 GND MOSI/DQ0 10
11 NC Reset 12

Contents :

  • 1 x SF600Plus Programmer
  • 1 x USB Cable
  • 1 x AC Power Adaptor (ME-SW-ADP-1)
  • 1 x ISP Cable (ISP-600-CB1-G)
  • 1 x SF100 2.54mm 2*4 ISP Cable (ISP1-CB)
  • 1 x SF600 Universal Adaptor (ADP-SF600-TO-SF100)
  • 1 x CD-ROM (Included Software, specifications and user manual)

Hardware Requirement for ISP :

To have a clear understanding on the different ISP or backup boot methods and different reference schematics, please download our dedicated application notes,AN0103 and AN0106 for further use. [Download]

Option Purchase :

  • Backup Boot Flash-SO8N
  • Backup Boot Flash-Dual SO8N
  • Backup Boot Flash-SO8W
  • Backup Boot Flash-Dual SO8W
 　
  • Backup Boot Flash-SO16W
  • Backup Boot Flash-Dual SO16W
  • BBF SO8 Testclip
  • BBF SO8 Testclip-Dual
 　
  • BBF SO16W Testclip
  • ISP SO8 Testclip
  • ISP SO16W Testclip
  • SF100 Universal Adaptor