Description :

EM100Pro is DediProg Serial Flash Emulator based on RAM memory in order to offer the best update performances. This advanced tool has been designed in close cooperation with the Serial Flash suppliers to emulate the behaviors of all the market Serial Flash and also the next generation Serial Flash.

Features :

  • Emulate all the market Serial Flash in one click
  • Support upto two 256Mb or one 512Mb SPI flash emulation
  • Support Dual IO & Quad IO
  • Support Dual flashes emulation
  • Update code in less than 3 seconds
  • USB powered & palm size
  • Support Windows 2003 and above & Support both 32 bit or 64 bit OS

Benefits :

  • Minutes becomes seconds for SPI Flash code update (3 seconds to update 256Mb SPI Flash)
  • Save up to 1 hours every days for your development and reduce your time to market
  • Debug efficiently your application through the available SPI bus with our SPI Trace, SPI Trigger, SPI Hyper Terminal for debug messages
  • Develop your own application debugger via our bidirectional SPI Hyper terminal and control application from your host PC
SPI Flash Emulation Interface SPI Bus Trace Interface
SPI Hyper Terminal Interface 　
　
Performance (Erase+Program+Verify)
Density 512Kb 1Mb 2Mb 4Mb 8Mb 16Mb 32Mb 64Mb 128Mb 256Mb
Programmer 3s 4s 6s 12s 18s 35s 40s 90s 190s 290s
EM100Pro 3s 3s 3s 3s 3s 3s 3s 3s 3s 3s

Hardware :

The EM100Pro has two 2.54mm pitch males connectors of:

  • 2*2 for the Reset and Trig signals
  • 2*10 for the Emulation signals
EM100pro is designed with ISP header, through an appropriate connector, users can connect the programmer and drive the SPI signals, supply the memory and control the controller or application status. Please refer to Table 1 for the EM100pro 2x10 header pin out.
DediProg also provides the ISP cable for Intel's motherboard. It can be used to connect the EM100pro/SF600 programmer and mated with the 2x10 connector(Samtec:ASP-159358-03). please refer to Table 2 for the 2x10 pin out. Click Here to get further information about this cable.
Table 1: EM100pro ISP Header Pin Out (2x10),(2x2) 　 Table 2: lSP-ADP-Intel-B Pin Out (2x10)
1 Hold2 CS2 2
3 CS1 Vcc 4
5 MISO/DQ1 Hold1/DQ3 6
7 Wp1/DQ2 CLK 8
9 GND MOSI/DQ0 10
11 3.3V Wp2 12
13 CTRL NC 14
15 CTRL 3.3V 16
17 CTRL CTRL 18
19 GND CTRL 20

1 GND Reset 2
3 GND Trig 4
　

　
1 KEY CS0 2
3 RESET CS1 4
5 GND VCC3_3 6
7 CLK DQ2/WP 8
9 DQ3/HOLD MISO 10
11 X MOSI 12
13 X X 14
15 X X 16
17 X X 18
19 X X 20
Contents :
  • 1 x EM100Pro
  • 1 x USB 2.0 cable
  • 1 x ISP-ADP-Intel-B
  • 1 x 2.54mm 2x10 to 1.27mm 2x4/2x8 SO connection adaptor
  • 1 x 12cm EM100Pro split cable
  • 1 x Software and User Manual in CD
 　
  • 4 x 1.27mm 2x8 SMT male header  (10.3mm)
  • 4 x 1.27mm 2x4 SMT male header (6.0mm)
  • 4 x 1.27mm 2x4 SMT male header (10.3mm)
  • 3 x 15cm single wire with 2.54mm Dupont head
  • 1 x EM100Pro Reference Flash Adaptor (SO8W)
  • 1 x EM100Pro Reference Flash Adaptor (SO16W)
  • 2 x Grabber Clip